Mouse Test: Click, Double Click, Scroll & Polling Rate Checker

Quick answer: Click inside the mouse test below with each button, including the two side buttons. Every working button lights up and counts your clicks. If a single click ever registers as two clicks less than 80 ms apart, the switch is double clicking and is starting to fail. Use the other tabs to check your scroll wheel for skipping, measure your polling rate in Hz and test your clicks per second.

Last updated: November 20, 2026

Mouse test

Check every mouse button, catch double-clicking (switch chatter), test the scroll wheel, measure your polling rate and run a click speed test. Nothing to install.
Click here with each mouse button, including the side buttons.
Left0Not tested
Middle (wheel)0Not tested
Right0Not tested
Back (side)0Not tested
Forward (side)0Not tested
Single-click each button 20 to 30 times at a normal pace. A healthy switch never shows a double click warning.
↕
Hover here and scroll slowly up, then slowly down.
Scroll up0Wheel steps
Scroll down0Wheel steps
Wrong-way jumps0Should stay at 0
Last step–Scroll distance
Scroll steadily in one direction. If the page jumps the wrong way while you scroll, the wheel encoder is dirty or worn.
Current polling rate
0
Move your mouse in fast circles inside this box for a few seconds.
Highest0 HzPeak reading
Average0 HzWhile moving
Likely setting–Detecting method
Chrome and Edge give the most accurate reading. Some browsers cap mouse updates at your screen’s refresh rate, which makes the reading lower than your real polling rate.
0.0
Click here to start. Click as fast as you can until the timer runs out.
Clicks0This round
Time left5.0 sCountdown
Best CPS0.0This visit

How to test your mouse

  1. Buttons and double click: click inside the box 20 to 30 times with each button at a normal pace. Every button should count up, and no double click warnings should appear.
  2. Scroll wheel: hover over the box and scroll slowly in one direction, then the other. The wrong-way jumps counter should stay at zero.
  3. Polling rate: move the mouse in fast circles inside the box. The highest reading shows roughly how often your mouse reports its position.
  4. Click speed: pick a test length and click as fast as you can to get your clicks per second (CPS).

Mouse double clicking when you single click: causes and fixes

A mouse that double clicks on its own almost always has a worn switch. Inside each button is a small metal leaf that wears and bounces over time, so one press makes two contacts. Before replacing anything, try these fixes:

  • Check Windows first. In Settings, Bluetooth and devices, Mouse, Additional mouse settings, make sure the double-click speed is not set to the fastest end, and that ClickLock is off.
  • Discharge static. Unplug the mouse (or remove its battery), hold the buttons down for 30 seconds, then reconnect. This sometimes clears a temporary fault.
  • Raise the debounce time. Many gaming mouse apps from Logitech, Razer, SteelSeries and others have a debounce or click delay setting that filters out double clicks.
  • Clean the switch. Short blasts of compressed air into the gap around the button can clear dust from the contacts.
  • Use the warranty. Double clicking is a hardware fault, and most gaming mice have a 1 to 2 year warranty. Mice with optical switches do not suffer from this problem at all.

Scroll wheel skipping or jumping

If the page jumps the wrong way while you scroll, the wheel’s encoder is dirty or worn. Blow compressed air into the gaps on both sides of the wheel while rolling it, update the mouse’s firmware, and try a different USB port. If skipping keeps happening after cleaning, the encoder needs replacing.

What polling rate should I use?

Polling rateReports everyGood for
125 Hz8 msOffice use, very old computers
500 Hz2 msCasual gaming
1000 Hz1 msThe standard for gaming mice
4000 Hz0.25 msHigh refresh rate monitors, competitive players
8000 Hz0.125 msTop-end esports setups with a fast CPU

1000 Hz is the sweet spot for most players. Rates of 4000 Hz and above feel smoother on 240 Hz and faster monitors, but they use more CPU and some older games can stutter. You change the polling rate in your mouse’s software or with a button underneath it.

What is a good click speed?

Most people click around 6 to 7 times per second. Anything above 8 CPS is fast, and players who use jitter clicking or butterfly clicking can reach 10 to 15 CPS or more. Fast clicking puts more wear on your mouse switches, so do not be surprised if a mouse that has spent years in click speed tests starts double clicking.

FAQ

Why does my mouse double click when I single click?

Usually because the switch inside the button is worn or dirty. Confirm it with the double click test above, then try the fixes in this guide. If it continues, replace the switch or use your warranty.

How do I check my mouse’s polling rate?

Open the Polling rate tab and move your mouse in quick circles inside the box. Use Chrome or Edge for the most accurate reading, because some browsers limit mouse updates to your screen’s refresh rate.

Why do the side buttons go back a page?

Browsers use the side buttons for back and forward. Inside the test box, this tool blocks that so you can test them safely. Outside the box, they work normally.

Is 1000 Hz polling rate good for gaming?

Yes. 1000 Hz means your mouse reports its position every millisecond, which is the standard for gaming mice and plenty for almost everyone.

Does this mouse test work on a laptop touchpad?

The button, scroll and click speed tests work with touchpads too. The polling rate test is meant for mice, since touchpads report at different rates.

More hardware tests: Keyboard tester · Controller tester and stick drift test

Our guides are researched, fact-checked and updated as games change. How we research and verify our guides.